972-709-6259 stateassessor@aol.com

INSPECTION VS. TESTING

Airborne Environmental provides two services;

1. Inspections
2. Testing.

Though it is not always necessary to do both, it is usually recommended for the following reasons:

1. In some cases, an air test might reveal a high indoor spore count even though there is no visible evidence of mold. In this can, the inspection alone would not detect a mold problem even though one exists.

2. Conversely, a visual inspection may turn up evidence of surface mold even though an air test might show spore counts well within a normal range. In this case, the air test alone would not reveal a mold problem even though one exists.

The combination of a visual inspection and an air test is optimal for assessing mold conditions since one typically points to the other.

VISUAL INSPECTION EXPLAINED…

An inspection is a visual inspection of the property, inside and out, for evidence of mold and signs of water intrusion. The Visual Inspection reveals obvious molds on surfaces and helps determine hidden mold problems that may go unnoticed to an un-trained eye. A visual inspection can also uncover existing and potential moisture problems in construction materials. Wet or damp wood, drywall, and even concrete may not be a mold problem now, but will be if ignored. Airborne Environmental Consultants uses specialized electronic equipment to detect moisture levels of construction materials such as stucco, wood siding, plaster, drywall, cabinets, shower stalls and floors.

SAMPLING & TESTING EXPLAINED

We are now offering a new service for anyone who wants limited information regarding moisture prevention  assessment ; mold assessment.

  1. Visual inspection inside the house for moisture intrusion or mold.
  2. Analytical tests in areas where mold samples are taken.  Humidity, temperature, and measurements..
  3. First air sample with outdoors for comparison of air indoors.
  4. If there are visible areas of suspected mold, we will take 2-3 tape lift from areas.

WHAT TO EXPECT

  • Mold assessment report of finding
  • Management Plan
  • Post Remediation Verification:
  • Visual inspection with no air sample $200.00 to $350.00
  • Cost per mileage $0.50 each way

RESIDENTIAL COST BELOW

Commercial Property add $100.00

VISUAL INSPECTION

$200-350
  • Up to 3,000 Square Feet
  • No Air Samples
  • Inspect Property Inside/Out
  • Reveal Hidden Mold Problems
  • Reveal Existing Moisture Problems
  • Reveal Potential Moisture Problems
  • Moisture Mapping Building Materials
Contact Us

INFRARED INSPECTION

$500
  • Free With Mold Inspection
  • Up to $3,000 Square Feet
  • Inside Inspection under Pier Beam
  • HVAC Inspection
  • Moisture Testing Plumbing Areas
  • Analytics in All Sampling Areas
  • Mold Sampling
  • Digital Photos of Damage
  • CAD Drawing Of Property
  • Analysis of Data
  • Written Mold Assessment Report
  • Written Mold Management Plan
  • Written Mold Remediation Protocol
  • License & Accreditation’s
  • Payment Due When Work Submitted
  • Written Assessment In 10 Days or Less
Learn More

SAMPLING

QUOTED
  • Visual Inspection Included
  • Analytical Testing
  • Testing Humidity, Temp, & Measurements
  • Control Sample Outdoors
  • Indoor Samples Compared To Outdoor Sample
  • If Visible Mold, Then 2-3 Tape Samples
  • Mold Assessment Report of Finding
  • Management Plan
  • Post Remediation Verification
  • 1 HVAC Unit – 3 Air Samples
  • 2 HVAC Units – 3 Air Samples
  • 3 HVAC Units – 3 Air Samples
  • If 12 or More Samples Needed, They Will Be Quoted
Contact Us

SAMPLING PACKAGES

We believe that a limited survey of this nature will allow residential home owner’s , real estate agents, insurance adjustors , property managers, and lenders to identify if mold problem exists and whether a full investigation is warranted.